Bathtub Stopper Won’t Stay Down? Here’s How to Fix It

A bathtub stopper is a small device that is used to plug the drain of a bathtub. The stopper is usually made of rubber or plastic, and it is inserted into the drain hole to prevent water from flowing out. There are different types of bathtub stoppers, but the most common one is the suction cup stopper.

If your bathtub stopper won’t stay down, it can be a real pain. The good news is that there are a few things you can do to fix the problem. In this post, we’ll show you how to fix a bathtub stopper that won’t stay down.

Why won’t my bathtub stopper stay down?

Reason-1:

One of the most common reasons a bathtub stopper won’t stay down is that it needs to be replaced. Over time, the rubber or silicone seal on the stopper can wear down, making it less effective at sealing the drain. In addition, the metal components can also become corroded or damaged, making it difficult for the stopper to stay in place.

Reason-2:

Another common reason a bathtub stopper won’t stay down is that there is something blocking the drain. This could be anything from hair to soap scum to dirt and debris. If you can see what’s blocking the drain, you can try to remove it with a plunger or a plumber’s snake. However, if you can’t identify the blockage, it’s best to call a professional to clear the drain.

Reason-3:

In some cases, a bathtub stopper won’t stay down because the drain itself is faulty. If the drain is cracked or damaged, it may not create a tight seal, causing the stopper to pop up. This is a more serious problem that will require the assistance of a professional to fix.

Reason-4:

Finally, if you have a bathtub with an overflow drain, it’s possible that the stopper is not properly aligned with the drain. When the stopper is in the wrong position, it can cause water to leak out of the overflow drain, making the stopper pop up.

How to fix a bathtub stopper that won’t stay down?

If your bathtub stopper won’t stay down, there are a few things you can do to fix it. First, try adjusting the screw that holds the stopper in place. If that doesn’t work, you can try replacing the washer on the stopper. If neither of those solutions works, you may need to replace the entire stopper.

To adjust the screw, start by removing the cap on the stopper. Then, use a screwdriver to turn the screw clockwise or counterclockwise until the stopper is tight or loose enough that it will stay in the down position.

If adjusting the screw doesn’t work, you can try replacing the washer. To do this, start by removing the screw and then the washer. Take the new washer and place it on the stopper, then replace the screw. Tighten or loosen the screw until the washer is snug.

If neither of those solutions works, you may need to replace the entire stopper. To do this, start by removing the screw and washer. Then, pull the stopper out of the drain. Take the new stopper and place it in the drain, then replace the washer and screw it. Again, tighten or loosen the screw until the washer is snug.

Hopefully one of these solutions will fix your bathtub stopper so that it stays down.

Some tips for preventing a bathtub stopper from not staying down

Assuming you would like tips on how to keep your bathtub stopper in good working order:

1. First, take a look at the drain hole to see if there is any hair or debris around it. If there is, use a plunger to try and remove it.
2. If the drain hole is clear, check to see if the stopper is properly inserted. It should fit snugly in the drain hole.
3. If the stopper is properly inserted and the drain hole is clear, there may be a problem with the stopper itself. Try running some hot water down the drain to see if that melts any built-up gunk.
4. If the stopper is still not staying down, you may need to replace it. You can purchase a new stopper at most hardware stores.
5. To install the new stopper, simply insert it into the drain hole and give it a few twists to secure it in place.

FAQ

How much does it cost to replace a bathtub drain stopper?

Bathtub drain stoppers typically cost between $15 and $25 to replace.

Why is my pop-up plug not working?

There could be a few reasons why your pop up plug is not working. The most common reason is that the seal around the plug is not tight enough, allowing water to seep in and around the plug. Another reason could be that the plug is not inserted properly into the drain, which can cause a leak. Lastly, the plug could be old and needs to be replaced.

Why does my bath plug keep popping up?

There are a few reasons that your bath plug might be popping up. One possibility is that the chain that is attached to the plug is too short, and when you pull the plug out, the chain isn’t long enough to keep the plug down. Another possibility is that there is something blocking the drain, such as a hair clog, and when the water tries to drain, it pushes the plug up.

Conclusion

If your bathtub stopper won’t stay down, there are a few things you can try to fix the issue. First, check to see if the stopper is properly aligned with the drain. If it is not, try adjusting it. If that doesn’t work, you can try using a plunger to push the stopper down. If the stopper is still not staying down, you may need to replace it.