How to install a bathtub without access underneath

If you’re installing a bathtub, you’ll need to have access to the underside in order to do so. However, if you don’t have access to the underside, don’t worry! You can still install a bathtub without it.

In this blog post, we’ll show you how to install a bathtub without access underneath. We’ll go over the tools you’ll need and the steps you’ll need to take in order to get the job done.

Installing a Bathtub Without Access Underneath

STEP 1: Gather your supplies

• Tape measure
• Level
• Tub
• Caulk
• Drill
• Screws
• Shims

STEP 2: Cut a hole in the drywall

If you need to install a bathtub and do not have access underneath, you will need to cut a hole in the drywall. This is a relatively easy task, but there are a few things you need to keep in mind.

• First, make sure you have the correct tools. You will need a drill, a saw, and some drywall screws.
• Second, make sure you measure the hole correctly. You do not want to make the hole too big or too small.
• Third, when you cut the hole, be careful not to damage any of the surrounding drywall.
• Fourth, when you install the bathtub, make sure it is level and secure.
• Fifth, when you are finished, patch the hole in the drywall and repaint it.

STEP 3: Install the brackets

If you are installing a bathtub without access underneath, you will need to use brackets to secure it in place. Brackets are available at most hardware stores. Follow the manufacturer’s instructions for installation.

STEP 4: Set the tub in place

If you’re planning to install a bathtub without access underneath, you’ll need to take a few extra steps to make sure everything is properly in place.

First, set the tub in its desired location and mark the spots where the feet will rest on the floor. Then, remove the tub and use a drill to create holes in the floor at the marked locations. Next, insert shims into the holes and set the tub back in place. Finally, use a level to make sure the tub is level and secure it in place with screws.

STEP 5: Secure the tub

If you are installing a tub without access to the underside, you will need to secure it in place with screws. First, mark the location of the tub on the floor. Then, pre-drill holes through the floor at the marks. Next, place the tub in the desired location and insert screws through the pre-drilled holes. Finally, use washers and nuts to secure the screws in place.

FAQs

Can you install a bathtub without access underneath?

Yes, you can install a bathtub without access underneath. However, you will need to use a different installation method, such as a drop-in bathtub, which does not require access underneath.

How do you install a bathtub without access underneath?

There are a few different ways to install a bathtub without access underneath. One method is to use a drop-in bathtub, which does not require access underneath. Another method is to install the bathtub using a different installation method, such as a freestanding bathtub.

What are the benefits of installing a bathtub without access underneath?

There are a few benefits of installing a bathtub without access underneath. One benefit is that you will not need to worry about water damage if there is a leak in the tub. Another benefit is that you will not need to access the underside of the tub, which can be difficult to reach.

Are there any drawbacks to installing a bathtub without access underneath?

There are a few drawbacks to installing a bathtub without access underneath. One drawback is that you will not be able to use a traditional installation method, such as a freestanding bathtub. Another drawback is that you may need to use a different type of tub, such as a drop-in bathtub.

What are some tips for installing a bathtub without access underneath?

There are a few tips for installing a bathtub without access underneath. One tip is to use a drop-in bathtub, which does not require access underneath. Another tip is to install the bathtub using a different installation method, such as a freestanding bathtub.

Conclusion

If you need to install a bathtub and don’t have access underneath, you’ll need to do a few things differently. First, you’ll need to create a platform for the tub to sit on. You can do this by screwing 2x4s together to create a frame. Once the frame is in place, you’ll need to put down a layer of plywood and then cover it with tile or another type of flooring. Finally, you’ll need to install the tub itself. This can be done by using a tub installation kit.